3D Printing Materials

Exquisite white-8006

Introduction of 3D Printing Materials

Characteristics

SZUV-W8006  

PRODUCT DESCRIPTION 

SZUV-W8006 is an ABS like SL resin which has accurate and durable features. It is designed for solid state SLA platforms. SZUV-W8006 can be applied in master patterns, concept models, general parts and functional prototypes in the field of automotive, medical and consumer electronics industries.The parts duability building with SZUV-W8006 is over 6.5months.SZUV-W8006 TYPICAL FEATURES -Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines -Improved strength retained, improved dimensions retention of parts in humid condition -need minimal part finishing -Long shelf life in machine TYPICAL BENEFITS -Need less part finishing time,easier post-curing -Buliding accurate and high tough parts with an improved dimensional stability -High quality controls for vacuum casting parts -Low shrink and good resistance to yellowing -Magnificent white color -Outstanding machinable SLA material Physical Properties – Liquid Material 

Appearance	White
Density	1.13g/cm3 @ 25 ℃
Viscosity	376 cps @ 27 ℃
Dp	0.148 mm
Ec	7.8 mJ/cm2
Building layer thickness	0.1mm

 Mechanical Properties of Post-Cured Material 

MEASUREMENT	TEST METHOD	VALUE
		90-minute UV post-cure
Hardness, Shore D	ASTM D 2240	87
Flexural modulus, Mpa	ASTM D 790	2,592-2,675
Flexural strength, Mpa	ASTM D 790	70- 75
Tensile modulus, MPa	ASTM D 638	2,599-2,735
Tensile strength, MPa	ASTM D 638	39-56
Elongation at break	ASTM D 638	13 -20%
Poisson`s Ratio	ASTM D 638	0.4-0.43
Impact strength notched Izod, J/m	ASTM D 256	35 - 45
Heat deflection temperature, ℃	ASTM D 648 @66PSI	62
Glass transition,Tg，℃	DMA，E”peak	73
Coefficient of thermal expension, /℃	TMA(T<Tg)	95*E-6
Density, g/cm3		1.16
Dielectric Constant 60 Hz	ASTM D 150-98	4.6
Dielectric Constant 1 kHz	ASTM D 150-98	3.9
Dielectric Constant 1 MHz	ASTM D 150-98	3.6
Dielectric StrengthkV/mm	ASTM D 1549-97a	14.9

 Note: the temperature of szuv-w8006 should not be too high. Please use it below 25c.Recommended temperature for use and preservation is 18-25 ℃

Fire Fighting Measures

（1） extinguishant

 Dry powder fire extinguishing agent, alcohol resistant foam extinguishing agent, carbon dioxide, dry sand, spray water.

（2） Special risk

 Fires may produce irritation and harmful gas

（3） The firemen of protective measures

 Fireman should wear protective appliances (eye protection, protective clothing, mailing gas with gas mask, etc.), put out the fire in the windward.

6. Accidental Release Measures

（1） Homework personnel protective equipment

 Ensure adequate ventilation, wear suitable protective clothing, make a good job in hand and eye/face protection.

（2） Environmental protection measures

 Prevent products from entering the drain or open water

（3） Cleaning method

 For a small amount of leakage, use dry sand, soil and towels absorb the residual liquid, recycling and airtight container.

 For a large number of leakage, leakage of liquid can be in front of the embankment, the introduction of recycle to safe place.

（4） Secondary hazard prevention measures

 Quickly remove all fire spark (ban on smoking in nearby, and the ignition).

7. Handling And Storage

（1） Operation treatment technical measures

 Avoid contact with eyes, skin and clothing. Don't inhaling mist or steam, don't accidentally swallow, keep container tightly closed after the thorough cleaning.

（2） Partial or full ventilation   Maintain adequate ventilation

（3） Safe handling matters needing attention   No smoke, no fire

（4） Safe storage conditions

 Stored in a cool, well ventilated place, away from heat, sparks and flames. Keep container tightly closed until it is put into use.

（5） packaging container and material

 In the process of custody, please do not transfer to other containers. Don't fall back to the original containers of products that will be used.

Cases

SOME OF MY PROJECTS

Education

Rapid prototype

Auto Parts

Constructional design

Art Design

Medical